◥ Base Length: Setting FIBC big bag form-fit spout liner length
◥ Measured Length: Actual measured FIBC big bag form-fit spout liner length
◥ Base Speed: Setting the quantities of FIBC big bag form-fit spout liner per minute
◥ Actual Speed: Currently system big bag form-fit spout liner making speed
◥ Offset Length: (for special equipment)
◥ Total Length: The sum of the accumulated running length, after clearing, enter to reset meter counting
◥ Parcel ( the quantities of fibc form-fit spout liner ): Cumulative (parcel quantities setting) sum of batches, reset to record batches after clearing
◥ Count (the quantities of fibc form-fit spout liner ): Cumulative quantities
◥ Parcel quantities setting: The quantity of each batch can be preset according to the needs, and each batch will be alarmed to take big bag form-fit spout liners 5 in advance, and the preset value will be automatically cleared and reset to record the quantity
◥ Working Ways: Including printed doypack, unprinted doypack and flat big bag form-fit spout liner ( Printed doypack is the photoelectric tracking method, which is suitable for color printing fibc form-fit spout liner; unprinted doypack is cutting to length method, the photoelectric does not work, unprinted doypack is made by the dragging motor according to set big bag form-fit spout liner length, and the photoelectric and floating rollers do not work )
◥ Code Seeker Button: After the photoelectricity is lost when making printed doypack, click this button to get back the original position
◥ Reset Quantity: reset making big bag form-fit spout liner quantities
◥ Forward Manual Pulling: This button gradually shortens to jog running. Press and hold this button for more than 6 seconds and it will be in a long-running state. Only need to jog again to stop
◥ Edge Trimmer Cutting : Click this button once, the edge trimmer will move once
◥ Pulling Factor: If the setting drag material value is small, the dragging time is short, but the feeding is easy to shake. If the setting drag material value is large, the dragging time is long, and the feeding time is slow and stable. In the case of no pressing, a higher feed ratio should be adopted as much as possible
◥ Photoelectric Range: The effective range of positioning the photoelectric head within a few millimeters before and after the base length
◥ Convey: To set the time for the conveyer belt to move, an appropriate value should be set according to the size of the FIBC bag form-fit spout liner
◥ Valve Holing Time: The punching holing device (the round hole at the welding nozzle) maintains the action time. When the big bag form-fit spout in-liner making speed is accelerated, the set action time should be appropriately reduced. Generally set to 400 ~ 500ms
◥ Length Magnification: Off, 1-8 length magnifications. If it is set to off, the length magnification will not work (only used when there is no welding tip )
◥ Holing Type: On, interval, off
◥ Tension Offset: Adjust according to the working state of the tension dancer roller during operation
◥ Bottom Offset: Bottom offset is only available when the FIBC bag form-fit spout in-liner making type is unprinted doypack printed doypack
◥ Knife Switch: Using for special machines
◥ Valve up Welding Time: Set the appropriate value firmly according to the welding tip
◥ Valve low Welding Time: Set a value 50ms larger than the time of the valve up welding
◥ Running Speed: The current machine runs beats per minute
◥ Edge Trimmer Valve Setting: It is extremely important to set the position when opening length magnification
◥ Film Press Time: The upper mechanism of the edge trimmer presses the material time, so that the edge trimmer completes the cutting within the pressing time
◥ Form-fit Spout Edge Trimmer Setting: It is extremely important to set the position when opening length magnification
◥ Valve Magnification Setting: Magnification can be set freely
◥ Dancer Roller Switch: It is used for intermediate servo offset, dancer roller on is automatic offset, dancer roller off is without offset, when working type is set to unprinted (doypack / printed doypack), this function is automatically turned off
◥ Material Pulling: The servo feed proximity sensor displays the status, and this signal is very important
◥ Material Pulling Latency Time: It is detected that the servo motor of the material pulling proximity sensor starts to run after the set delay value time arrives
◥ Manual Pulling Speed: Used to set the speed of inching dragging, generally set to 800Hz
If you need to know about FIBC big bag aluminium form-fit spout in liner making machine, please click on model LinerSHAPE-ALC